Olivetti 145D User Manual Page 64
- Page / 88
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
62
1. Press the upper or lower part of the key
until the display shows:
SETTINGS
2. Press function key F3:
The display shows:
PIN CODE
3. Press function key F3:
The display shows:
PIN CODE ?
4. Type the default PIN on the keypad of the cordless
phone. Then press function key F3:
The display shows:
NEW PIN ?
5. Type the new PIN on the keypad of the cordless phone.
Then press function key F3:
The display shows:
CONFIRM PIN ?
6. Type the new PIN again on the keypad of the cordless
phone. Then press function key F3:
The display shows:
PIN CODE
7. To exit from programming mode, press function key
F1 twice:
NOTA
In step 4, if you type and confirm an incorrect code, the cordless
phone beeps and prompts you to type the PIN again. If you
think you have typed a wrong digit, you can delete it by
pressing the
key.
In step 6, if you type and confirm a code different from the one
set in step 5, the cordless phone beeps and prompts you to
type the PIN code again.
TO RESTORE THE DEFAULT PARAMETERS
If desired, you can restore the default parameters
(name of cordless phone, warning tones, ringing vo-
lume and tune, PIN, etc.) as follows:
1. Press the upper or lower part of the key
until the display shows:
SETTINGS
2. Press function key F3:
The display shows:
PIN CODE
3. Press the upper or lower part of the key
until the display shows:
RESTORE SETTINGS
4. Press function key F3:
The display shows:
PIN CODE ?
5. Type the PIN on the keypad of the cordless phone.
Then press function key F3:
The cordless phone restores the default parameters:
this operation takes a few seconds. At the end of the
procedure, the cordless phone returns automatically
to stand-by mode.
NOTA
If you can’t remember the PIN, you can restore the default
parameters. Proceed as follows:
1. Remove the batteries from the cordless phone.
2. Keep the
key of the cordless phone pressed, while you
reinsert the batteries in their compartment (make sure you
respect the battery polarities indicated).
3. The display of the cordless phone shows the message
"RESTORE SETTINGS".
4. Press function key F3 (
): the cordless phone restores the
default parameters, as indicated at the end of the previous
procedure.
TO SET THE ALARM
If desired, you can program the cordless phone to
ring at a set time, to act as an alarm or reminder.
1. Press the upper or lower part of the key
until the display shows:
DATE AND TIME SETTINGS
2. Press function key F3:
The display shows:
SET DATE
3. Press the upper or lower part of the key
until the display shows:
SET ALARM
4. To program the alarm, press function key F3:
5. Type the time at which you want the cordless phone to
ring. Then press function key F3:
The display shows:
1 2 3 4 5
6. To choose one of the 5 available ringing tunes, press
the upper or lower part of the key:
7. To confirm your choice, press function key F3:
The display shows:
ALARM REPEAT
- INSTRUCTIONS 1
- Copyright © 2007, Olivetti 2
- OPERATING PRECAUTIONS 6
- IMPROPER USE 6
- OMPONENTS 11
- HOW TO GET STARTED QUICKLY 12
- IMPORTANT 13
- PARAMETERS 14
- Important 20
- WHAT DOCUMENTS MAY BE USED 21
- TO SEND A DOCUMENT 21
- MANUAL RECEPTION 22
- AUTOMATIC RECEPTION 22
- TO CHOOSE THE RECEPTION MODE 22
- TELEPHONE 23
- INCOMING CALLS Û 24
- OUTGOING CALLS Ü 24
- CALL TRANSFER 24
- PLEASE WAIT 24
- WHAT DOCUMENTS CAN BE COPIED 25
- TO MAKE A COPY 25
- CONTENTS 27
- RANSMISSION 29
- RECEPTION 29
- OPERATIONS 29
- TO ADJUST THE RESOLUTION 30
- DOCUMENT READY 31
- THAT IS ALREADY SET 33
- LESS PHONE 35
- HOW TO READ THE REPORTS 38
- TRANSMISSION 39
- ANSWERING 41
- TO SET THE TAD ACCESS CODE 42
- DEVICE IN LOCAL MODE 43
- TO RECORD OUTGOING MESSAGE 1 43
- TO RECORD OUTGOING MESSAGE 2 44
- TO ERASE OUTGOING MESSAGE 2 44
- TO RECORD MEMOS 45
- TAD/FAX 03 46
- TAM MESSAGES 46
- PLAY MSG 01 03 46
- DELETE OLD MSG? 47
- NO 47
- DELETE OLD MESSAGES? 47
- OUTGOING MESSAGE ONLY 48
- TOLL SAVER 48
- SOPHISTICATED 50
- TO DISPLAY THE CALLER ID 51
- TO CHANGE THE RING VOLUME 52
- FREQUENCY 53
- TO CHANGE THE SILENCE LAPSE 54
- TO SET THE BLACK LIST 55
- TO MODIFY THE BLACK LIST 56
- TO DELETE THE BLACK LIST 56
- TO PRINT THE BLACK LIST 57
- TO HEAR THE LINE SIGNALS 57
- O REGULATE THE SPEAKER VOLUME 58
- O REGULATE THE BUZZER VOLUME 58
- TO ENABLE/DISABLE ECM 59
- FIRST OF ALL, WHAT POLLING IS 60
- TO CHANGE THE RINGING VOLUME 62
- TO CHOOSE THE TUNE 62
- TO CHANGE THE PIN 63
- TO SET THE ALARM 64
- TO SELECT A BASE UNIT 65
- ROUBLESHOOTING 67
- ACOUSTIC ERROR SIGNALS 69
- ERROR MESSAGES ON THE DISPLAY 69
- OTHER ACOUSTIC SIGNALS 70
- OTHER MESSAGES ON THE DISPLAY 70
- CORDLESS 72
- AINTENANCE 73
- ANUFACTURER 78
- CUSTOMER 78
- ECHNICAL 79
- ORIGINAL CONSUMABLES 87
- 259749B-01 88
© 2020, manymanuals.com. All rights reserved. | 0.125 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals